BWHeader

Mix of Stuff 16 February 2012

Today I was asked to make a red target icon that doesn’t look like the target used by Target. I googled archery targets to get a notion of what might be visually expected. I didn’t remember that the center of a target could be yellow.

Whenever I perform searches for work projects, I often receive hits that are of personal interest. Today I found arrows at the Museum of Anthropology, the University of Missouri. I made several series based on weapons, so I’m always delighted to see lovely artifacts that also have a dark edge to them. I especially like sharp pointy objects.

Arrows1Arrows2

According to the site the artifacts are Javanese target arrows. The description states that the shafts are made of bamboo, a material that I have used quite often in my work. I found that it was a bit difficult obtaining the surface that I wanted until I hit on using heat. Beware though, bamboo can catch fire from the inside. Before you know it, your piece can be aflame.

I chose to use bamboo because it is a prolific grower, its cultural myths, and its use in a variety of rituals.

After I finished the icon job, I went out to water a newly planted hellebore. I noticed that the bottlebrush in the courtyard apparently doesn’t like its location. It is thrusting out from the house and in doing so appears to be using a bunny ornament as a support.

Weight

When I went back to proofing the database of thousands of words, I found a couple of interest–

antemeridian
of, relating to, or taking place in the morning

antefix
carved ornament at the eaves of a tile roof concealing the joints between tiles


New Find-Solder Wick

I was visiting my neighbor who refurbishes musical instruments and he showed me a roll of Solder Wick.

Solder Wick Roll

I asked what it was used for, I hadn’t yet looked at the name which would have been a clue. I was taken with the woven aspect of the material, and it is copper.

Solder Wick 1

Solder Wick is used for wicking away solder, or desoldering. I tend to look at most things as possible materials for use in a piece. The image above is deceptive because the material is not much wider than dental tape.

I think Solder Wick would be great to use as a binding material. The woven braid detail would be a wonderful element for loads of pieces. I will need to check the specifics about whether the rosin flux coating might affect the melt point and interact with my glazes.

Typically I make a bunch of test pieces and fire them up. It is always exciting opening a kiln. What gifts will I be given? I never feel that an unexpected effect is a mistake. It might be the best gift or information to file away for possible use on a different piece.


This is a detail of a piece with some metal sent through a low fire glaze. The piece was then fired with a bottle of Acetaminophen. The dose should be enough for coma.

The Dose Makes the Poison Detail


The vessel is made of hardware cloth held together with nails, coated with Egyptian Paste, and fired to cone 016.

Paste Detail


I am still thinking about the combination of materials used in this piece. I like the straight pins, and the bit of drippy glaze on them. I added a bottle of Ibuprofen to the interior of the cup and fired it again. I had hoped that the Ibuprofen would either become dry and powdery or molten and run between the pins. The pills changed color, but stayed pretty much intact. Couldn’t fire higher because of the glaze and metal used. The foot of the cup is washers bound on with bronze wire.
Pin Cup

Solder Wick can be purchased online or at some local hardware stores. I can’t believe that this was the first time I’ve seen it.

The product images are from Wikipedia .


Might Come In Handy Some Day

I have been accused of being a pack rat. Sure there is a tad of truth to that description. But I should think that most mixed media artists know–collected materials for use “some day” could mean exactly that.

Many of the pieces that I had in a show last year had materials I saved for several years. For example, the pit fired cup was a demo piece from a teaching gig over 10 years ago. The metal bits I snagged when my brother-in-law was clearing out his warehouse of construction materials.

At Risk


I wanted this cup to appear more goblet-like so I drilled a hole through the bottom to attach a carriage bolt for a stem. The stem has two types of washers that are filling in for the dots and dashes of Morse Code.

The stem has the word “mourning” in code. It is a play on the homophone “morning” as in morning cup of tea. The small bag inside the cup has poison plant bits–not material appropriate for a tea ceremony.

Mourning Cup


The wood for the sides of the next piece came from an old swing that I rescued from my parents’ burn pile. That was more years ago than I care to remember. The bronze bit on the rosary is a piece of a dried fig that was spin cast in the late 80s. I couldn’t find a home for it until this piece was made. The rosary has “Cleanse Your Palate” and “Forgive Yourself” in code.

The thing that was most fun about constructing this piece was how the cast soap cup came into existence. I made a slew of woven and fiber cups that I meant to cast in bronze. I never managed to get them gated and cast so they were stored away. When I ran across them I realized that I really didn’t want to cast them any longer. So, I made silicone molds for casting soap and sugar pieces.

Forgive Yourself


Rarely do I first glimpse a material or object and know precisely how I will use it. Often materials make it known where they would like to live and with whom.

When I was sorting out the stuff in Dad’s barn, I collected materials to ship home. This is some of what I collected.

Metal Bits

The metal drawers have been nicely oxidized from mice living in them.

Metal Drawers

So many possibilities…